RENO TH is a highly integrated ultra-low power embedded certified module supporting Thread and NFC-A tag. RENO interfaces to user’s MCU with UART and SPI. This small form-factor module reduces the system cost and gives design flexibility by including all the analog front-end, crystals and antenna.
RENO TH module is based on Nordic nRF52840 SoC. This module offloads the host processor and reduces user’s development cost and time to market with integrated wireless stacks, network stack, and application APIs and all the advanced security features supported by ARM Trust Zone Cryptocell-310. Module comes in industrial temperature.
Typical Applications
- Personal fitness devices
- Wearables Connected health
- Climate controls(HVAC)
- Smart home sensors and controllers
- Industrial IoT sensors and controllers
- Thread SDK with certified Open Thread stack released by Nest
- Low power wireless mesh networking protocol
- Support device-to-device and device-to-cloud communications
- Support for the AT commands for easy evaluation and Binary APIs for production
- Highlights of iVativ APIs and AT commands
- Ready to use on all popular MCUs with zero or negligible porting effort
- Seamless integration for RTOS or bare-metal based user application
- Agnostic to underlying SoC. / Chipset and its respective SDKs / firmware
- Secure boot enabled
- OTA FW update support
- Support for UART and SPI to interface with host MCU. AT commands support over UART and Binary APIs support over UART and SPI interfaces
- Highly optimized hardware for ultra-low power consumption with excellent performance
- ARM® Crypto Cell 310 cryptographic accelerator and AES 128 bit encryption
- Over the air device firmware upgrade (OTA DFU)
| Wireless Protocols | Thread, NFC-A |
| Frequency | 2.402 – 2.480 GHz |
| On air data rates | 802.15.4 – 250kbps |
| Thread throughput | 80kbps |
| Security Features | ARM Crypto Cell 310, 128-bit AES HW accelerator, Secure boot |
| Antenna options | PCB Trace Antenna or MHF4 connector |
| Programmable output power | -20dBm to +8dBm |
| Receive Sensitivity | – 100dBm at 250kbps |
| Current consumption | 450nA – Deep sleep mode 1.5µA – System standby mode |
| GPIO | 46 configurable |
| Range | TBD |
| Power supply and operating voltage range | Integrated DC-DC, 1.7v to 5.5v |
| Operating Temperature | -40oC to 85oC |
| Humidity | 5-90% non-condensing |
| Package | 10mm x 15mm x 1.5mm, 0.5mm pitch |
| Thread Stack | Open thread 1.1.1 |
| Certifications and approvals | FCC, IC, CE |
Product Brief |
168 KB
|
||
Quick Start Guide |
284 KB
|
||
EVK User Guide |
5 MB
|
||
Data Sheet |
2 MB
|
- RENO TH DVK
- RENO TH EVK
- 1 x Micro USB cable
- 1 x Mini USB cable
- NFC antenna
- STM32F411 MCU board
-Fill the form and submit or drop an email at sales@ivativ.com
| Part No | Protocol | Architecture | Dimensions (L x W x H) in mm |
Package | Antenna | Description | |
|---|---|---|---|---|---|---|---|
| I540E009-I2LT | Thread + NFC | Embedded | 10 x 15 x 1.5 | LGA | PCB | RENO Thread and NFC module with PCB Antenna, Tray packing | Buy |
| I540E009-I2LR | Thread + NFC | Embedded | 10 x 15 x 1.5 | LGA | PCB | RENO Thread and NFC module with PCB Antenna, Tape and Reel packing | Buy |
| I540E009-I3LT | Thread + NFC | Embedded | 10 x 15 x 1.5 | LGA | MHF4 | RENO Thread and NFC module with MHF4 Antenna connector, Tray packing | Buy |
| I540E009-I3LR | Thread + NFC | Embedded | 10 x 15 x 1.5 | LGA | MHF4 | RENO Thread and NFC module with MHF4 Antenna connector, Tape and Reel packing | Buy |
